Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Do not ignore the forklift at the workplace. If the procedure is not good, there will be major mishaps in minutes, and there are lots of mishaps including forklifts.

Situation 1: The forklift freight obstructed the motorist's view, and the individual ahead might not be found, resulting in a rolling accident.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty products, the workers utilized their body weight as the counterweight, which practically triggered casualties.
Case 3: The width of the forklift freight goes beyond the allowed width of the path and hangs on the roadside rack, which virtually creates an mishap.
Case 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not notice the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the personnel unlawfully, the forklift vehicle driver does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift rolls over.
Instance 7: The forklift motorist did not wear a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift operation need to take notice of these matters ：.

Beginning.
1. Prior to starting, observe the environments, and after verifying that there are no barriers that impede the safety of driving, honk the horn first and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale should be secure before beginning.
3. When the forklift starts with a lots, the chauffeur should first validate that the tons is secure and trustworthy.
4. The start needs to be slow and consistent.

Driving.
1. When driving, the height between the bottom end of the fork and the ground need to be kept at 300mm-400mm, and the pole should be tilted in reverse. .
2. Do not lift the fork too expensive when driving. When getting in and leaving the job website or while driving, be careful that there will be no barriers overhead. When the load is taking a trip, the fork has to not be raised expensive, which will impact the security of the forklift. .
3. After dumping, the fork should be reduced to the regular driving placement before driving. .
4. When turning, if there are pedestrians or cars close by, the driving signal needs to be issued first. High-speed sharp turns are banned. High-speed doglegs will cause the car to shed side security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the factory and need to maintain a specific safety and security range from the lorry ahead. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be effectively slanted back. The lots will not be increased other than when stacking or packing. .
8. The height of the load must not obstruct the vehicle driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when turning around.
9. It is prohibited to switch on the ramp, nor to drive throughout the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold items and play a stabilizing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely fashion, and they will certainly never run with health problems or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the lots of both forks balanced and not manipulated, and one side of the item need to protest the rack. .
2. It is restricted to deal with a solitary fork or utilize a fork top or pull. In unique circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging things, the forklift should be stopped with the brake. .
4. The speed of the lorry ought to be slow-moving and stable. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled things and hurt individuals. .
5. When using a fork to fork the goods, the fork must be as deep as feasible under the tons, and it needs to be noted that the fork idea should not touch other items or objects. The tons should be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted onward slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at high speed and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to loaf the fork, so regarding avoid the collapse of the goods and hurt people. .
8. Overwhelming is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to make use of the brake inertia to slide, put, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet unload.

Leaving .
1. It is prohibited to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you need to discharge the goods or reduced the fork framework.
2. Draw the emergency brake manage to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the automobile's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look needs to be examined, and gas, lubricating oil and cooling water should be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leakage needs to likewise be inspected and the seals should be changed Stand-on Electric Pallet Stacker in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the car;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the nadir of the freight ought to be 0.3 m ~ 0.4 m in the air;.
5. The transforming should not be as well sharp to prevent the propensity of " totally free turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the incline is enabled.
7. Do not drive across the slope. When the gradient is above 10%, the car needs to be driven backwards when worsening;.
8. When the forklift workers lug the goods and progress, if they run into big or hefty goods and most likely to the chauffeur's view, they should take the turning around exercise
.
The "Eight Prohibitions" must be adhered to in the operation.
1. Solitary fork operation is not enabled.
2. It is not permitted to lift the goods for far away driving.
3. It is not permitted to pick up the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with Electric Forklift Truck for Warehouse forks.
5. It is not enabled to utilize inertia pressure to pick up the goods.
6. It is not enabled to make use of braking force to exile round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on inclines
.
Car parking is not permitted under the list below problems.
1. Contours, slim roads, railway crossings;.
2. Sections with a longitudinal slope above 5%.
3. When there is an barrier on one side of the roadway, the opposite side of the section with the same length as the challenge must be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844